Surface doping of rubrene single crystals by molecular electron donors and acceptors.

The surface molecular doping of organic semiconductors can play an important role in the development of organic electronic or optoelectronic devices. Single-crystal rubrene remains a leading molecular candidate for applications in electronics due to its high hole mobility. In parallel, intensive research into the fabrication of flexible organic electronics requires the careful design of functional interfaces to enable optimal device characteristics. To this end, the present work seeks to understand the effect of surface molecular doping on the electronic band structure of rubrene single crystals. Our angle-resolved photoemission measurements reveal that the Fermi level moves in the band gap of rubrene depending on the direction of surface electron-transfer reactions with the molecular dopants, yet the valence band dispersion remains essentially unperturbed. This indicates that surface electron-transfer doping of a molecular single crystal can effectively modify the near-surface charge density, while retaining good charge-carrier mobility.

Coordination of Tetracyanoquinodimethane-Derivatives with Tris(pentafluorophenyl)borane Provides Stronger p-Dopants with Enhanced Stability.

Strong molecular dopants for organic semiconductors that are stable against diffusion are in demand, enhancing the performance of organic optoelectronic devices. The conventionally used p-dopants based on 7,7,8,8-tetracyanoquinodimethane (TCNQ) and its derivatives "FxTCN(N)Q", such as 2,3,4,6-tetrafluoro-7,7,8,8-tetracyanoquinodimethane (F4TCNQ) and 1,3,4,5,7,8-hexafluorotetracyano-naphthoquinodimethane (F6TCNNQ), feature limited oxidation strength, especially for modern polymer semiconductors with high ionization energy (IE). These small molecular dopants also exhibit pronounced diffusion in the polymer hosts. Here, we demonstrate a facile approach to increase the oxidation strength of FxTCN(N)Q by coordination with four tris(pentafluorophenyl)borane (BCF) molecules using a single-step solution mixing process, resulting in bulky dopant complexes "FxTCN(N)Q-4(BCF)". Using a series of polymer semiconductors with IE up to 5.9 eV, we show by optical absorption spectroscopy of solutions and thin films that the efficiency of doping using FxTCN(N)Q-4(BCF) is significantly higher compared to that using FxTCN(N)Q or BCF alone. Electrical transport measurements with the prototypical poly(3-hexylthiophene-2,5-diyl) (P3HT) confirm the higher doping efficiency of F4TCNQ-4(BCF) compared to F4TCNQ. Additionally, the bulkier structure of F4TCNQ-4(BCF) is shown to result in higher stability against drift in P3HT under an applied electric field as compared to F4TCNQ. The simple approach of solution-mixing of readily accessible molecules thus offers access to enhanced molecular p-dopants for the community.

Spectral Signatures of a Negative Polaron in a Doped Polymer Semiconductor: Energy Levels and Hubbard U Interactions.

The modern picture of negative charge carriers on conjugated polymers invokes the formation of a singly occupied (spin-up/spin-down) level within the polymer gap and a corresponding unoccupied level above the polymer conduction band edge. The energy splitting between these sublevels is related to on-site Coulomb interactions between electrons, commonly termed Hubbard U. However, spectral evidence for both sublevels and experimental access to the U value is still missing. Here, we provide evidence by n-doping the polymer P(NDI2OD-T2) with [RhCp*Cp]2, [N-DMBI]2, and cesium. Changes in the electronic structure after doping are studied with ultraviolet photoelectron and low-energy inverse photoemission spectroscopies (UPS, LEIPES). UPS data show an additional density of states (DOS) in the former empty polymer gap while LEIPES data show an additional DOS above the conduction band edge. These DOS are assigned to the singly occupied and unoccupied sublevels, allowing determination of a U value of ∼1 eV.

Improving the Resistance of Molecularly Doped Polymer Semiconductor Layers to Solvent.

The ability to form multi-heterolayer (opto)electronic devices by solution processing of (molecularly doped) semiconducting polymer layers is of great interest since it can facilitate the fabrication of large-area and low-cost devices. However, the solution processing of multilayer devices poses a particular challenge with regard to dissolution of the first layer during the deposition of a second layer. Several approaches have been introduced to circumvent this problem for neat polymers, but suitable approaches for molecularly doped polymer semiconductors are much less well-developed. Here, we provide insights into two different mechanisms that can enhance the solvent resistance of solution-processed doped polymer layers while also retaining the dopants, one being the doping-induced pre-aggregation in solution and the other including the use of a photo-reactive agent that results in covalent cross-linking of the semiconductor and, perhaps in some cases, the dopant. For molecularly p-doped poly(3-hexylthiophene-2,5-diyl) and poly[2,5-bis(3-tetradecyl-thiophene-2-yl)thieno(3,2-b)thiophene] layers, we find that the formation of polymer chain aggregates prior to the deposition from solution plays a major role in enhancing solvent resistance. However, this pre-aggregation limits inclusion of the cross-linking agent benzene-1,3,5-triyl tris(4-azido-2,3,5,6-tetrafluorobenzoate). We show that if pre-aggregation in solution is suppressed, high resistance of thin doped polymer layers to solvent can be achieved using the tris(azide). Moreover, the electrical conductivity can be largely retained by increasing the tris(azide) content in a doped polymer layer.

Use of a Multiple Hydride Donor To Achieve an n-Doped Polymer with High Solvent Resistance.

The ability to insolubilize doped semiconducting polymer layers can help enable the fabrication of efficient multilayer solution-processed electronic and optoelectronic devices. Here, we present a promising approach to simultaneously n-dope and largely insolubilize conjugated polymer films using tetrakis[{4-(1,3-dimethyl-2,3-dihydro-1H-benzo[d]imidazol-2-yl)phenoxy}methyl]methane (tetrakis-O-DMBI-H), which consists of four 2,3-dihydro-1H-benzoimidazole (DMBI-H) n-dopant moieties covalently linked to one another. Doping a thiophene-fused benzodifurandione-based oligo(p-phenylenevinylene)-co-thiophene polymer (TBDOPV-T) with tetrakis-O-DMBI-H results in a highly n-doped film with bulk conductivity of 15 S cm-1. Optical absorption spectra provide evidence for film retention of ∼93% after immersion in o-dichlorobenzene for 5 min. The optical absorption signature of the charge carriers in the n-doped polymer decreases only slightly more than that of the neutral polymer under these conditions, indicating that the exposure to solvent also results in negligible dedoping of the film. Moreover, thermal treatment studies on a tetrakis-O-DMBI-H-doped TBDOPV-T film in contact with another undoped polymer film indicate immobilization of the molecular dopant in TBDOPV-T. This is attributed to the multiple electrostatic interactions between each dopant tetracation and up to four nearby anionic doped polymer segments.

Understanding the evolution of the Raman spectra of molecularly p-doped poly(3-hexylthiophene-2,5-diyl): signatures of polarons and bipolarons.

Molecular doping is a key process to increase the density of charge carriers in organic semiconductors. Doping-induced charges in polymer semiconductors result in the formation of polarons and/or bipolarons due to the strong electron-vibron coupling in conjugated organic materials. Identifying the nature of charge carriers in doped polymers is essential to optimize the doping process for applications. In this work, we use Raman spectroscopy to investigate the formation of charge carriers in molecularly doped poly(3-hexylthiophene-2,5-diyl) (P3HT) for increasing dopant concentration, with the organic salt dimesityl borinium tetrakis(penta-fluorophenyl)borate (Mes2B+ [B(C6F5)4]-) and the Lewis acid tris(pentafluorophenyl)borane [B(C6F5)3]. While the Raman signatures of neutral P3HT and singly charged P3HT segments (polarons) are known, the Raman spectra of doubly charged P3HT segments (bipolarons) are not yet sufficiently understood. Combining Raman spectroscopy measurements on doped P3HT thin films with first-principles calculations on oligomer models, we explain the evolution of the Raman spectra from neutral P3HT to increasingly doped P3HT featuring polarons and eventually bipolarons at high doping levels. We identify and explain the origin of the spectral features related to bipolarons by tracing the Raman signature of the symmetric collective vibrations along the polymer backbone, which - compared to neutral P3HT - redshifts for polarons and blueshifts for bipolarons. This is explained by a planarization of the singly charged P3HT segments with polarons and rather high order in thin films, while the doubly charged segments with bipolarons are located in comparably disordered regions of the P3HT film due to the high dopant concentration. Furthermore, we identify additional Raman peaks associated with vibrations in the quinoid doubly charged segments of the polymer. Our results offer the opportunity for readily identifying the nature of charge carriers in molecularly doped P3HT while taking advantage of the simplicity, versatility, and non-destructive nature of Raman spectroscopy.

An Organic Borate Salt with Superior p-Doping Capability for Organic Semiconductors.

Molecular doping allows enhancement and precise control of electrical properties of organic semiconductors, and is thus of central technological relevance for organic (opto-) electronics. Beyond single-component molecular electron acceptors and donors, organic salts have recently emerged as a promising class of dopants. However, the pertinent fundamental understanding of doping mechanisms and doping capabilities is limited. Here, the unique capabilities of the salt consisting of a borinium cation (Mes2B+; Mes: mesitylene) and the tetrakis(penta-fluorophenyl)borate anion [B(C6F5)4]- is demonstrated as p-type dopant for polymer semiconductors. With a range of experimental methods, the doping mechanism is identified to comprise electron transfer from the polymer to Mes2B+, and the positive charge on the polymer is stabilized by [B(C6F5)4]-. Notably, the former salt cation leaves during processing and is not present in films. The anion [B(C6F5)4]- even enables the stabilization of polarons and bipolarons in poly(3-hexylthiophene), not yet achieved with other molecular dopants. From doping studies with high ionization energy polymer semiconductors, the effective electron affinity of Mes2B+[B(C6F5)4]- is estimated to be an impressive 5.9 eV. This significantly extends the parameter space for doping of polymer semiconductors.

Single-Step Formation of a Low Work Function Cathode Interlayer and n-type Bulk Doping from Semiconducting Polymer/Polyethylenimine Blend Solution.

The use of polyethylenimine (PEI) as a thin interlayer between cathodes and organic semiconductors in order to reduce interfacial Ohmic losses has become an important approach in organic electronics. It has also been shown that such interlayers can form spontaneously because of vertical phase separation when spin-coating a blended solution of PEI and the semiconductor. Furthermore, bulk doping of semiconducting polymers by PEI has been claimed. However, to our knowledge, a clear delineation of interfacial from bulk effects has not been published. Here, we report a study on thin films formed by spin-coating blended solutions of PEI and poly{[N,N'-bis(2-octyldodecyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5'-(2,2'-bithiophene)} [P(NDI2OD-T2)] on indium tin oxide. We observed the vertical phase separation in such films, where PEI accumulates at the bottom and the top, sandwiching the semiconductor layer. The PEI interlayer on ITO reduces the electron injection barrier to the minimum value determined by Fermi level pinning, which, in turn, reduces the contact resistance by 5 orders of magnitude. Although we find no evidence for doping-induced polarons in P(NDI2OD-T2) upon mixing with PEI from optical absorption, more sensitive electron paramagnetic resonance measurements provide evidence for doping and an increased carrier density, at a very low level. This, in conjunction with an increased charge carrier mobility due to trap filling, results in an increase in the mixed polymer conductivity by 4 orders of magnitude relative to pure P(NDI2OD-T2). Consequently, both interfacial and bulk effects occur with notable magnitude in thin films formed from blended semiconductor polymer/PEI solution. Thus, this facile one-step procedure to form PEI interlayers must be applied with attention, as modification of the bulk semiconductor polymer (here doping) may occur simultaneously and might go un-noticed if not examined carefully.

Towards understanding the doping mechanism of organic semiconductors by Lewis acids.

Precise doping of organic semiconductors allows control over the conductivity of these materials, an essential parameter in electronic applications. Although Lewis acids have recently shown promise as dopants for solution-processed polymers, their doping mechanism is not yet fully understood. In this study, we found that B(C6F5)3 is a superior dopant to the other Lewis acids investigated (BF3, BBr3 and AlCl3). Experiments indicate that Lewis acid-base adduct formation with polymers inhibits the doping process. Electron-nuclear double-resonance and nuclear magnetic resonance experiments, together with density functional theory, show that p-type doping occurs by generation of a water-Lewis acid complex with substantial Brønsted acidity, followed by protonation of the polymer backbone and electron transfer from a neutral chain segment to a positively charged, protonated one. This study provides insight into a potential path for protonic acid doping and shows how trace levels of water can transform Lewis acids into powerful Brønsted acids.